Gas Fires Post War

The production of Gas Fires had stopped well before the second world war and no development had taken place since the 1930’s which is why this section has been separated from the earlier one in which the fire designs have a significantly ‘old fashioned’ appearance.

The Company had been heavily involved in wartime activities and continued with armament production right up until the middle of 1954. It was clear that new products were needed for the post war era and the development of the Halcyon warm air heaters was underway but was a slow process. Coincidentally, about the same time, 1954, Suggs’ acquired the Cowper Penfold company via an introduction by Bob Young who was Company Accountant to both companies. Cowper wished to retire, remaining for only a short consultancy period after the sale. The CP company had developed a number of gas fires and it was these that provided the new impetus with both convector fires and balanced flues.

Gas Fires for a ‘Modern’ World

  Sussex fire 260

Sussex

The ‘Sussex’ – Radiator?

Catalogued in a third party list as a ‘Gas Radiator’, the Sussex is one of the first radiant/convector gas fires produced after the war. More likely to be seen in an office or factory, the design did not suit the growing concept of fireplaces that were wider than they were high which was in due course to drive the appliance design into the completely opposite rectangular shape!

 CP Screen Fire 260

Screen Fire

The ‘CP’ Screen Fire

The Screen Fire, produced at a similar time is extraordinary to the modern way of thinking in that it is a portable gas fire intended to be simply placed in an existing fireplace and plugged in to the ‘gas poker point’ that was always provided beside the hearth of a coal fire to enable the coal to be easily and quickly lit!

Queen Convectair 60 

The ‘Queen Convectair’

Here at last was a fire that lived up to it’s name. The ‘Queen fire’, as it was more normally called, was particularly effective at providing convected warm air in addition to the relatively small area of radiant heating. The whole of the front consisted of a pierced sheet metal panel enabling large movements of the air that was heated up by the products of combustion. These passed through a large steel clamshell-type box before passing out to the flue. A classic of its time, it was considered by many to be one of the best fires ever produced.

Lady demonstrators 550

These splendid ladies are part of the team of lady demonstrators employed by the gas boards to demonstrate domestic appliances. Here they are discussing a plug-in poker in front of a gas fire display with a Sugg Screen Fire on the right.

UNDER CONTINUOUS DEVELOPMENT – PLEASE TRY AGAIN LATER

Copyright © Chris Sugg 2006-13

Top of page
or
Back to Heating

2 comments on “Gas Fires Post War
  1. Margaret Grant says:

    I have a Sugg Queen gas fire in my Brighton house (inherited from my mother), still in good working order (recently serviced by a Gas Safe engineer), though now with signs of old age. Specifically, he thinks the Control knob on top of the fire (not visible in your photograph) may break soon. Is there any hope of replacing it?

    Of less importance, the ignition lead for automatic lighting doesn’t work, but I am happy to continue lighting the fire with matches.

    Thanks in advance for any help/advice. What a wonderful fire it has been. They don’t make them like that any more.

    • Chris Sugg says:

      Gosh, Margaret, that must make your Queen Fire at least 60 years old! I do get messages from people with ancient Sugg appliances but mostly they are lamps although I do recall the odd Halcyon warm air heater still going strong. The Queen Fire was very good at its job because of the completely pierced front panel but other companies were coming up with wide rather than tall gas fires that looked more ‘modern’ and the Queen design had a limited life!
      Most control knobs of that sort of age have a ‘D’ shaped spindle with a spring clip and will slide off the spindle if pulled upwards. It shouldn’t be impossible to find a knob that fits the ‘D’ even if it is not identical.
      Actually the Queen Fire was before my time but most igniters have a push button piezo ignition system which is still used on all sorts of appliances and even the lead and spark plug – for sake of a better name – can be found. What you need is a good gas repair man to dig out the bits and pieces you need and find a way to fit them in place of the originals. Finding the man is the real secret!

Leave a Reply

Your email address will not be published. Required fields are marked *

*